Short Answer
For an inside-mount blind or shade, measure the width at the top, middle and bottom and order the narrowest number, measure the height in three spots and order the longest, and don’t take any deductions yourself. For curtains, plan the rod first: usually 4 to 6 inches above the window frame and a few inches to about 6 inches past each side. Then pick panels that add up to 1.5 to 2 times the rod width, and measure the length from where the top of the panel will sit down to where you want the hem.
This box contains affiliate links. As an Amazon Associate I earn from qualifying purchases. See the affiliate note at the bottom of this post.
🧰 What I Use
Two things I reach for before I order anything for a window:
- My 2-foot level, to draw a level line for the curtain rod instead of trusting the window trim
- My stud finder, to see where the brackets can actually land before I settle on a rod width
🛒 Helpful Picks
These are well-reviewed options, not my personal picks.
Most blinds and curtains that look wrong were measured wrong. The blind has gaps on both sides, the curtains stop two inches short of the floor, or the panels barely close. None of it is hard to get right. It just takes a steel tape, a pencil, and about ten minutes per window. Here’s how I measure before anything gets ordered.
Before You Measure
- Use a steel tape, not a cloth sewing tape. Cloth stretches.
- Measure to the nearest 1/8 inch and don’t round down. Home Depot’s blinds and shades measuring guide says the same thing.
- Write width first, then height (W x H), and label every number with the room and window. “Bedroom left” saves a lot of guessing later.
- Measure every window, even ones that look identical. In older East Side houses, two windows in the same room can be off by a quarter inch or more.
- Note what’s in the way: window cranks, locks, alarm sensors, a heat register under the window, an outlet, or a door swing next to it.
Measuring for Blinds and Shades
Decide on inside mount (inside the window opening) or outside mount (on the wall or trim above it) before you measure, because the numbers are completely different.
Inside Mount
- Check the depth. Measure from the window glass or frame out to the front edge of the opening, and compare it to the minimum depth for the product you’re looking at. Bali’s wood and faux wood guide, for example, lists 3/4 inch as the minimum, with more needed to recess the blind fully. Every product is different, so check the spec.
- Width: measure inside the opening at the top, middle and bottom. Order the narrowest.
- Height: measure from the top of the opening to the sill at the left, center and right. Order the longest.
- Don’t deduct anything. The manufacturer takes off a small clearance on inside-mount orders. If you subtract too, you’ll get light gaps on both sides.
Outside Mount
- Width: measure the area you want covered, usually the outside edges of the trim, then add overlap. Bali recommends 1-1/2 inches per side, and Home Depot suggests about 3 inches extra overall for better light control and privacy.
- Height: measure from where the headrail will sit down to the sill or a little below it. Leave room for the headrail and brackets, which Home Depot notes can be up to 2-1/2 inches tall.
- Check the mounting surface. You need a flat spot, about 2 inches tall, above the window or on the trim. Thick or curved molding may need projection or extension brackets.
Once your blinds show up, here’s how to install window blinds so they’re level and stay in the wall.
Measuring for Curtains
With curtains, you’re really measuring for the rod first. Where the rod goes decides how wide and how long the panels need to be.
Step 1: Pick the Rod Height
Wayfair’s curtain measuring guide puts a standard rod 4 to 6 inches above the window frame, and 6 to 12 inches above it if you want the ceiling to look taller. A few things to check before you mark it:
- Crown molding or a low ceiling that leaves less room than you think.
- Other windows in the same room. Keep the rods at the same height so the room doesn’t look uneven.
- What’s in the wall. Above most windows there’s a wood header, which is great for brackets. Plaster in older homes needs a slow pilot hole and the right anchor where there’s no wood. If you’re not sure, here’s how to tell plaster from drywall.
Draw a light, level pencil line at that height. Don’t measure up from the trim at each end and connect the dots, because the trim in older houses often isn’t level.
Step 2: Pick the Rod Width
Measure the window from the outside edge of the trim on one side to the outside edge on the other. Then add extra on each side. A few inches works, and going about 6 inches per side lets the panels stack mostly off the glass when they’re open, so you get more light and the window looks bigger. Don’t count the finials in that number.
Wider rods need a center support bracket. Plan where it will go so it doesn’t land in the middle of the glass or block the panels from closing.
Step 3: Figure Out Panel Width (Fullness)
Curtains look best when there’s extra fabric to gather, even when they’re closed. Wayfair’s rule of thumb is a combined panel width of at least 1.5 times the window width, and usually about 2 times. Sheers can go fuller.
Example: a window that’s 36 inches across the trim, with 6 inches of rod on each side, gives you a 48-inch rod. Two times 48 is 96, so two panels about 50 inches wide each will look full without being bulky.
Step 4: Measure the Length
Measure from where the top of the panel will actually sit, down to where you want the hem. That starting point depends on the panel style:
- Grommet and rod-pocket panels ride on the rod, so the fabric starts at or a little above the top of the rod.
- Ring-clip or hook panels hang below the rings, so measure from the bottom of the ring.
Then pick where the bottom ends:
- Sill length: about 1/2 inch above the sill.
- Below the sill: a few inches past the bottom of the trim. Good over a radiator or heat register, where long fabric would block the heat.
- Floor length: about 1/2 inch above the floor. This is the cleanest look and the easiest to vacuum around.
- Puddled: several extra inches resting on the floor. It looks soft, but it collects dust and pet hair.
Measure the length at both ends and the middle, because floors aren’t always level. Store-bought panels come in set lengths, often 63, 84, 95 and 108 inches. If you’re close, it’s usually easier to nudge the rod height up or down an inch than to pay for hemming.
Blinds and Curtains on the Same Window
The easiest combination is an inside-mount blind with curtains on a rod outside the frame. If the blind is outside mount, the curtain brackets need enough projection to clear the blind’s headrail and valance, or the curtains will drag on it. Measure the blind’s depth before you buy the rod brackets.
Time and Difficulty
- Time: about 10 to 15 minutes per window if you’re careful. Plan a little longer for a room full of windows.
- Difficulty: easy. The only skill is patience and writing things down.
- Tools: steel tape measure, pencil, notepad or phone, level, step ladder, and a stud finder if you’re planning curtain rods.
Common Mistakes
- Ordering an inside-mount blind from the widest measurement instead of the narrowest.
- Taking your own deductions on an inside mount.
- Measuring one window and ordering the same size for the rest.
- Hanging the rod right on top of the trim, which makes the window look smaller.
- Buying one panel the width of the window and wondering why it looks flat.
- Measuring curtain length from the top of the window instead of from the rod.
- Forgetting the window crank, a heat register, or a door that swings into the curtain.
Safety
If there are young kids in the house, go cordless on blinds and shades. Corded window coverings are a strangulation risk, and the U.S. Consumer Product Safety Commission’s window covering rule now requires stock products to be cordless or have short or inaccessible cords. Keep cribs and climbable furniture away from windows, and while you’re at it, make sure dressers and TVs are anchored against tip-overs. Measure tall windows from a step ladder, not a chair.
DIY or Call a Guy?
DIY it if you’re ordering stock blinds or store-bought curtains for a few windows. Measuring is the easiest part of the whole job, as long as you take your time and write everything down.
Call someone if you’re ordering custom blinds or shades for a whole house, the windows are out of square or very tall, or you’d rather have one person measure and install so there’s no finger-pointing if something doesn’t fit. If your windows feel cold, it’s also worth checking for drafts before new coverings go up, and on older houses, storm windows may help more than heavy drapes.
Local to Euclid or Cleveland’s east side? I measure for and install blinds, shades and curtain rods myself. See my Blinds and Curtain Installation in Euclid & Cleveland page, or text me a photo at 216-800-5883.
FAQ
How high above the window should a curtain rod go?
Usually 4 to 6 inches above the frame. Going higher, partway to the ceiling, makes the window and the room look taller. Keep every rod in the room at the same height.
How far past the window should a curtain rod extend?
A few inches on each side at minimum. About 6 inches per side lets the panels clear the glass when they’re open, so you get more light.
How wide should curtain panels be?
Add up the panel widths and aim for about 1.5 to 2 times the rod width. One panel the exact width of the window will look flat and won’t close nicely.
Should curtains touch the floor?
For floor-length curtains, aim for about 1/2 inch above the floor. That looks finished and is easy to clean around. Let them puddle only if you like that look and don’t mind the dust.

Scan to join our Loyalty Program, get a free coupon for your next service, and stay up to date on our services and articles.
Affiliate Note
Some of the links in this article are affiliate links. That simply means if you choose to buy through them, I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. I only recommend products I trust and would feel comfortable installing in my own home or a client’s home.
If you try something I recommended and it turns out to be anything less than a five-star experience, please let me know. I always want these recommendations to be genuinely helpful.

