Short Answer
If your house already has hardwired smoke detectors, keep them hardwired and replace them with compatible hardwired units, ideally all at once. If your house has no wiring for alarms, 10-year sealed battery alarms are a solid choice, and wireless interconnected ones get you the “one goes off, they all go off” protection without running new wire. The best setup is whichever one you’ll actually keep working.
This box contains affiliate links. As an Amazon Associate I earn from qualifying purchases. See the affiliate note at the bottom of this post.
🧰 What You’ll Need
What I Use:
Ceiling alarms in hallways and over stairs are a reach. An adjustable ladder is safer than a chair.
Check price →
I use Klein for my electrical tools. Before you touch a hardwired alarm’s wiring, check that the breaker you flipped actually killed the power.
Check price →
Helpful Picks: these are well-reviewed options, not my personal picks. On hardwired systems, check the brand and connector on your existing alarms before you buy.
- Hardwired smoke alarms with 10-year battery backup
- Wireless interconnected 10-year battery smoke alarms
- Smoke alarm wiring adapter plugs (brand to brand)
Not sure what you have? If you’re in Northeast Ohio, text me a photo of one alarm, the label on the back and the plug behind it, and I’ll tell you what will fit.
Last updated: November 2026
How to Tell Which Kind You Have
You can usually tell from the floor, but it’s worth checking one alarm up close:
- Battery-only: the alarm twists off the ceiling and there’s nothing behind it but a plastic mounting plate and two screws.
- Hardwired: there’s a plug (a wiring harness) coming out of an electrical box behind the alarm, usually with three wires: black, white and a third wire, often red or yellow. Most hardwired alarms also have a small green or red power light that stays on.
- Hardwired and interconnected: that third wire is the interconnect. It’s what makes every alarm in the house sound when one detects smoke. Push the test button on one alarm. If they all go off, they’re interconnected.
Hardwired alarms still have a battery. It’s a backup for power outages, and it’s usually a 9-volt, AAs or a sealed 10-year battery. That backup is why a hardwired alarm can still chirp. If yours is chirping, start with Why Is My Smoke Detector Chirping?
Hardwired vs Battery: The Real Differences
Hardwired (with battery backup)
- Power: runs on your house’s 120-volt power, with a battery to cover outages.
- Interconnect: wired together, so a fire in the basement sets off the alarm outside your bedroom upstairs.
- Upkeep: fewer dead-battery problems, especially with models that have a sealed 10-year backup.
- Downside: replacing them takes a little more work, and brands don’t all use the same plug. More on that below.
Battery-only
- Power: replaceable batteries or a sealed 10-year lithium battery.
- Interconnect: standalone alarms only sound in the room they’re in. Wireless interconnected models link to each other by radio, no wires needed.
- Upkeep: replaceable-battery alarms need fresh batteries at least once a year. Sealed 10-year alarms don’t, but you replace the whole alarm at the end.
- Upside: easy to add anywhere: a bedroom that never had one, a finished attic, a basement in an older house.
Either type should be replaced every 10 years. The American Red Cross cites the NFPA and CPSC on that, because sensors lose sensitivity with age. Check the date on the back.
Which Should You Have?
Here’s how I’d decide:
Your house already has hardwired alarms: keep them hardwired. Don’t pull a hardwired alarm and stick a battery unit on the ceiling next to the box. You lose the interconnect for that spot and leave a live box behind it. Swap in new hardwired alarms on the same wiring.
Your house has no alarm wiring: that’s common in older East Side homes built before hardwired alarms were standard. Running new wire through finished plaster ceilings isn’t worth it for most people. Use 10-year sealed battery alarms, and if you can, go with a wireless interconnected set so they all sound together.
You have a mix: a lot of houses do. Maybe hardwired alarms in the hallways from a past remodel and nothing in the bedrooms. Keep the hardwired ones, and fill the gaps with battery alarms. If the hardwired brand makes a wireless-linked model that talks to its wired system, that’s the cleanest way to tie the new ones in. Check the manufacturer’s compatibility list before buying.
You’re building new or doing a major remodel: that’s not really your choice. The Red Cross notes that new homes need smoke alarms that are hardwired, interconnected and battery-backed, on every level, outside each sleeping area and in each bedroom. That’s part of the electrical work for the project.
For existing homes, the Red Cross says the minimum is an alarm on every level and outside each sleeping area, and that interconnected alarms in each bedroom and throughout the home give the best protection. My room-by-room placement guide covers where they go.
Replacing Hardwired Alarms: Like for Like, and the Brand Problem
This is where people get stuck. The plug on the ceiling is made for one brand’s alarm, and brands don’t share the same connector.
Easiest path: same brand, current model. Look at the label on the back of the old alarm. If it’s a Kidde, buy a current Kidde hardwired model. If it’s First Alert or BRK, stay with them. A lot of the time the new alarm plugs right into the existing harness, or comes with a new harness you connect to the same wires.
Switching brands: use the adapter plug. Both big brands sell adapters that let their alarm plug into the other brand’s harness. Kidde sells Quick Connect adapters for select First Alert and BRK harnesses, and First Alert has a wiring adapter compatibility guide for going the other way.
The catch is the interconnect. An adapter makes the plug fit. It doesn’t guarantee the alarms will talk to each other. Kidde says its alarms interconnect with other Kidde products and only the specific other-brand models on its tested compatibility list, and that mixing in other equipment can cause nuisance alarms, failure to alarm, or damage. First Alert’s guide says not to mix brands on the same interconnect wire at all.
So my advice is simple: if they’re interconnected, replace them all at once with one brand. They’re usually the same age anyway. If one is 10 years old, the rest are too.
How a Like-for-Like Swap Goes
- Buy the replacements, plus adapters if you’re changing brands.
- Turn off the breaker for the alarm circuit. It isn’t always labeled, so you may have to try a few.
- Twist the old alarm off and check the wires with a non-contact voltage tester before you unplug or disconnect anything.
- Unplug the old harness, or plug the adapter into it. If the new alarm comes with its own harness, connect it to the same wires (black to black, white to white, interconnect to interconnect) with the right wire connectors.
- Mount the new plate, plug in the alarm and twist it on.
- Turn the breaker back on, confirm the power light, and press test on each alarm. Every alarm in the house should sound each time.
Follow the manual for your specific alarm. Some need a pull-tab removed to activate the backup battery.
Common Mistakes
- Replacing just one interconnected alarm with a different brand. It may fit and still not trigger the others.
- Leaving a hardwired alarm unplugged and hanging. If it’s bad, replace it.
- Capping off the wires and going battery-only. You lose the interconnect and leave a live box behind a battery alarm.
- Skipping the test. Test every alarm after a swap, not just the new one.
- Buying by looks. Check sensor type too. Near kitchens, photoelectric causes fewer false alarms. My guide to smoke detector types explains the difference.
DIY or Call a Guy?
DIY if you’re putting up battery alarms, or swapping a hardwired alarm for the same brand on the same harness and you’re comfortable shutting off a breaker. More on that in Can You Install a Smoke Detector Yourself?
Call a guy if you’re changing brands on an interconnected system, the wiring behind the alarm is loose, brittle or doesn’t match the colors above, the alarms are over a stairwell or a high ceiling, or you’re replacing the whole house and want the layout checked while it’s being done.
Call a licensed electrician if you need new wiring: adding hardwired alarms where there was no box, running a new interconnect wire, or adding a circuit. Same if you see scorch marks, smell burning at an alarm, or a hardwired alarm has no power with the breaker on.
Local to Euclid or Cleveland’s east side? I replace and install smoke and CO detectors myself, battery and hardwired, including swapping out old interconnected systems. See my Smoke Detector Services in Euclid & Cleveland page, or text me a photo at 216-800-5883.
FAQ
Are hardwired smoke detectors better than battery ones?
Hardwired interconnected alarms give you the best warning across the whole house, and they don’t depend on you changing batteries. But a working battery alarm beats a hardwired one that’s been unplugged. Wireless interconnected battery alarms close most of the gap.
Can I replace a hardwired smoke detector with a battery one?
You can physically do it, but I don’t recommend it. You lose the interconnect for that spot and leave a live electrical box behind it. Replace hardwired with hardwired.
Do hardwired smoke detectors have batteries?
Yes. They have a backup battery for power outages, either replaceable or a sealed 10-year battery.
Can I mix brands of hardwired smoke detectors?
Only if the manufacturer lists them as tested compatible. First Alert says not to mix brands on the same interconnect wire. It’s simpler and safer to replace them all with one brand.
How often should smoke detectors be replaced?
Every 10 years, hardwired or battery. Check the date printed on the back. My take on whether 10-year sealed alarms are worth it may help you choose.

Scan to join our Loyalty Program, get a free coupon for your next service, and stay up to date on our services and articles.
Affiliate Note
Some of the links in this article are affiliate links. That simply means if you choose to buy through them, I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. I only recommend products I trust and would feel comfortable installing in my own home or a client’s home.
If you try something I recommended and it turns out to be anything less than a five-star experience, please let me know. I always want these recommendations to be genuinely helpful.
