Short Answer
Swapping a refrigerator water filter is a 5-minute job: buy the filter that matches your model, twist or push the old one out, put the new one in, and run a gallon or two through the dispenser to clear the air. Replacing the ice maker line takes longer, about 30 to 60 minutes. Shut the water off, pull the fridge out, and swap the old plastic line for a braided stainless one. If the valve feeding it is a saddle valve that clamps onto the pipe, that’s the part worth upgrading.
This box contains affiliate links. As an Amazon Associate I earn from qualifying purchases. See the affiliate note at the bottom of this post.
🛒 Helpful Picks
These are well-reviewed options, not my personal picks. For the filter itself, search your fridge’s model number and buy the one made for it.
- Braided stainless ice maker lines, so you’re not trusting thin plastic tubing behind the fridge
- Wi-Fi water leak sensors to set under the fridge, so a slow drip texts your phone instead of soaking the floor
- Appliance rollers that make pulling a full fridge out a lot easier on you and the floor
Most fridges with a water dispenser or ice maker have two parts that wear out: the water filter, which you’re supposed to change on a schedule, and the supply line behind the fridge, which most people never look at until there’s a puddle. Here’s how to do both, what to check while you’re back there, and when it makes sense to hand it off.
How Often to Change the Filter
Check your manual, but six months is the common answer. GE, for example, says to replace its filters every six months or after about 170 to 200 gallons, depending on the model, and sooner if the water flow to the dispenser or ice maker slows down.
Signs it’s overdue:
- The dispenser runs slow or the ice maker makes smaller cubes than it used to
- The water tastes or smells off
- The filter light is on (it’s usually just a timer, not a sensor, so it’s a reminder, not a test)
How to Replace a Refrigerator Water Filter
- Find your filter’s part number. It’s printed on the old filter and in your manual. Fridges in the same brand use different filters, so match it exactly. Look for NSF/ANSI certification on the package.
- Find where it lives. Common spots: the upper right corner inside the fresh food side, behind a door in the base grille, or in the back corner of the fridge. Some side-by-sides hide it behind a small door near the top.
- Put a towel under it. A few drops will come out. You don’t usually need to shut the water off for a filter swap.
- Remove the old filter. Most twist a quarter turn and pull out. Push-button types pop out when you press the release. If yours has a bypass plug, don’t lose it.
- Install the new one. Pull off any protective cap, line it up, and push or twist until it seats. Some brands tell you to fill the new filter with tap water first to cut down on air. Your manual will say.
- Flush it. Run water through the dispenser until it flows steady. GE says about 1 to 2 gallons clears the air on its models. Sputtering for the first few ounces is normal.
- Reset the filter light. It’s usually a button or a menu on the control panel. The manual tells you which one.
Replacing the Ice Maker Line
The line that feeds your fridge is usually one of three things: white or clear plastic tubing, soft copper tubing, or a braided stainless hose. Plastic is the one I’d replace. It gets brittle over time, kinks when the fridge gets pushed back, and when it cracks, it leaks until someone notices.
What to check first
- The shut-off valve. Follow the line back to where it taps into a water pipe. That’s usually under the kitchen sink or in the basement ceiling under the fridge. Make sure the valve actually closes.
- The fitting size. Most fridge inlets and valves use 1/4-inch compression fittings, but check both ends before you buy a line.
- The length. Measure the run, then buy a line with some slack so the fridge can come out for cleaning without pulling on it. Don’t buy one so long it gets crushed behind the fridge.
Steps
- Shut the water off at the valve feeding the fridge. If that valve won’t close, shut off the main.
- Unplug the fridge and slide it out. Go slow so you don’t tear up the floor.
- Put a towel and a small bucket under the connection on the back of the fridge. Unscrew the old line at the fridge, then at the valve.
- Thread the new line on by hand at both ends, then snug it with a wrench. Don’t crank it. Overtightened compression fittings leak too.
- Turn the water on slowly and check both ends for drips. Run your finger around the fittings; a slow weep is easier to feel than see.
- Plug the fridge back in, run a gallon or so through the dispenser, and look again before you push it back.
- Come back an hour later and check one more time.
About Saddle Valves
A saddle valve is a little valve that clamps around a copper pipe and pierces it with a needle. A lot of older ice maker hookups use one because it’s quick to put in. GE doesn’t recommend them: it says they don’t leave a big enough opening for the water, which can mean small, slow or hollow ice cubes. Home inspectors also point out that they leak more often than a proper valve.
If yours is working and not leaking, leave it alone until you’re ready to replace it, because opening and closing an old saddle valve can be what starts the leak. The better fix is a proper tee in the water line with a real shut-off valve. That means shutting off the house water and cutting into the pipe, so it’s a step up from swapping a hose.
Time, Difficulty and Tools
- Filter swap: 5 to 10 minutes, easy. No tools.
- Ice maker line: 30 to 60 minutes, easy to moderate. Two adjustable wrenches (or one wrench and pliers), a towel, a bucket, and a flashlight.
- Replacing a saddle valve with a tee and shut-off: moderate. Pipe cutter, the right fittings for your pipe, and confidence shutting off and draining the house water.
Common Mistakes
- Buying a filter that “should fit” instead of the one for your model number. A filter that doesn’t seal right can leak or let water bypass it.
- Skipping the flush, then thinking the new filter is bad because the water sputters or looks cloudy.
- Kinking the new line when the fridge goes back in. Push it back slow and watch the line.
- Overtightening plastic fittings until they crack.
- Not checking for leaks later. A slow drip behind a fridge can go weeks before anyone sees it.
Safety
- Unplug the fridge before you work behind it.
- A full fridge is heavy. Get help, or empty it first, and protect the floor.
- If water has been leaking under the fridge for a while, check for soft flooring or mold before you put it back.
DIY or Call a Guy?
DIY it for the filter, every time. It’s one of the easiest jobs in the house. Most people can handle the ice maker line too if the shut-off valve works and the fittings are standard.
Call someone if the shut-off valve won’t close or is a leaky saddle valve, the line runs through a cabinet or the basement ceiling, there’s already water damage, or you can’t move the fridge safely by yourself.
Local to Euclid or Cleveland’s east side? I replace shut-off valves and supply lines myself, so if the valve behind your fridge won’t close or the old line has seen better days, I can take a look. See my Plumbing Services in Euclid & Cleveland page, or text me a photo at 216-800-5883.
FAQ
Do I have to turn the water off to change the fridge filter?
Usually not. GE says its filters can be swapped with the water on. Keep a towel handy for the few drops that come out.
Why is my water sputtering after a new filter?
Air in the new filter. Keep running water through the dispenser until it flows steady, about 1 to 2 gallons on GE models.
Can I run the fridge without a filter?
Some fridges need a bypass plug in the filter slot or the dispenser and ice maker won’t work. Check your manual.
What’s the best ice maker line?
A braided stainless line with the right fittings and a little slack is the common upgrade over plastic tubing.
Why are my ice cubes small or hollow?
Low water flow. A clogged filter is the usual cause. A saddle valve or a kinked line can do it too.
Related Guides
- Should I turn off the main valve when leaving for vacation?
- Protect your outdoor faucets from freezing
- How to create a home maintenance checklist
- Rental turnover checklist (fridge lines and filters belong on it)
Sources
- GE Appliances: Replacing the Water Filter
- GE Appliances: Self-Tapping Water Valve
- Structure Tech: Saddle valves

Scan to join our Loyalty Program, get a free coupon for your next service, and stay up to date on our services and articles.
Affiliate Note
Some of the links in this article are affiliate links. That simply means if you choose to buy through them, I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. I only recommend products I trust and would feel comfortable installing in my own home or a client’s home.
If you try something I recommended and it turns out to be anything less than a five-star experience, please let me know. I always want these recommendations to be genuinely helpful.
