Short Answer
Most exterior doors made in the last few decades use a kerf-in weatherstrip: a foam or rubber seal with a fin that presses into a slot in the jamb. Pull the old strip out, clean the slot, and press in a new one that matches the profile, one continuous piece per side. Then fix the bottom with a new door sweep or door bottom, and adjust the threshold until a dollar bill drags when you pull it out from under the closed door. On older wood doors without a slot, use V-strip or a nail-on stop seal instead.
This box contains affiliate links. As an Amazon Associate I earn from qualifying purchases. See the affiliate note at the bottom of this post.
🧰 What You’ll Need
What I Use:
For pilot holes when you screw on a door sweep or nail-on stop seal. Pilot holes keep the screws straight and stop thin trim from splitting.
Check price →
Helpful Picks: these are well-reviewed options, not my personal picks. Match the profile and color to what’s on your door before you buy.
Start by Finding Where the Air Gets In
Don’t buy anything yet. Close the door on a cold, windy day and look for daylight around the edges, especially at the top corners and along the bottom. Then hold the back of your hand along the gaps, or slowly move a lit incense stick around the frame and watch where the smoke wavers. My guide on how to check your home for drafts walks through the whole house.
The other quick test is the dollar bill. Close the door on a bill at a few spots along the sides, top and bottom. If it slides out with no drag, the seal isn’t touching there.
Where the leak is tells you what to fix:
- Sides and top: the jamb weatherstrip is flattened, torn or missing.
- Bottom: the sweep or door bottom is worn, or the threshold is too low.
- One spot only, usually a top corner: the door may be out of adjustment, not the seal. More on that below.
- Around the outside trim: that’s a caulk job, not weatherstripping. Weatherstripping is for parts that move. Fixed gaps get caulk, as the Department of Energy’s weatherstripping guide points out.
Figure Out What Kind of Door You Have
Open the door and look at the jamb where the door closes against it.
Kerf-in seal. Most steel and fiberglass prehung doors have a thin slot (the kerf) cut into the jamb with a foam or rubber seal pressed into it. This is the easiest kind to replace and it’s what most people in newer or updated homes have.
No slot. Plenty of older East Side houses still have original wood doors in wood frames. If there’s no kerf, you’ll be adding a seal: V-strip (a tension seal that springs open in the gap), adhesive foam, or a nail-on seal that attaches to the door stop molding.
If you’re not sure what the different types are, my post on what weatherstripping is covers the materials.
Measure and Buy the Right Seal
- Bring a piece with you. Pull a short section of the old kerf seal and take it to the store, or compare it closely to the product photos. Profile matters: foam-filled, bulb and fin shapes don’t all fit the same slot.
- Measure each side and the top. Add a little extra. The DOE suggests adding 5 to 10 percent for waste, and I’d rather trim a long piece than come up short.
- For the bottom, measure the door width and thickness. Slide-on door bottoms are sized to door thickness, and many fit a 1-3/4″ exterior door.
- Match color if you care how it looks. White, brown and black are common.
How to Replace Kerf-In Weatherstripping
- Pull the old strip. Grab it at the top and pull straight out. It usually comes in one long piece. If the fin snaps off in the slot, pick it out with a putty knife or needle-nose pliers.
- Clean the kerf. Brush or vacuum out dirt, and wipe the jamb. A dirty slot is why new strips pop back out.
- Start with the hinge side or latch side, not the top. Cut the side pieces to run from the floor up to the head jamb. Some manufacturers want a mitered corner at the top; others butt the top piece against the sides. Follow the instructions on your package. Either way, the corners need to meet tight, because that’s where most leaks start.
- Press it in by hand, working from one end. Push the fin in with your thumbs or roll it in with a seam roller. Don’t stretch the strip as you go or it’ll shrink back and leave a gap.
- Do the top piece and cut it to fit snug between the sides.
- Close the door and test. The door should latch without you slamming it, and the dollar bill should drag all the way around. A brand-new strip can make the door a little stiff for a few days until it compresses.
Weatherstripping an Older Door With No Slot
On an older wood door, I’d go with V-strip on the hinge and latch sides and the top. Clean the jamb, cut each piece to length, and stick or tack it to the jamb so the open side of the V faces the outside. When the door closes, the V gets squeezed and seals the gap.
If the gaps are uneven, which is common in older frames that have shifted a bit, a nail-on seal attached to the stop molding is easier to adjust. Close the door, push the seal against it so the bulb just compresses, and tack it there. Work one side at a time.
Adhesive foam is the cheapest and quickest option, but it wears out fastest on a door you use every day. It’s fine for a back door that barely gets opened.
Fixing the Bottom: Sweeps, Door Bottoms and Thresholds
Door sweep
A sweep screws to the face of the door at the bottom, on the inside. Close the door, hold the sweep so the rubber or brush just touches the threshold, mark the screw holes, drill pilot holes, and screw it on. Most have slotted holes so you can fine-tune the height. Brush sweeps can drag on carpet or a rug, so check that before you commit.
Slide-on door bottom
Most steel and fiberglass doors use a U-shaped door bottom with fins that slide into slots on the bottom edge of the door. You’ll need to take the door off the hinges, or at least open it far enough to work underneath. Pull the old one out, clean the slots, and slide the new one in. A drop of soapy water helps it slide. Some also get a couple of small screws on the edge.
Adjustable threshold
Look at your threshold. If it has a row of screws or plastic caps along the top, it’s adjustable. Pop the caps off and turn the screws a quarter turn at a time (watch which way raises it on yours) until the door bottom seals but the door still closes without forcing it. Adjust all the screws evenly so the threshold doesn’t bow.
When the Problem Isn’t the Weatherstripping
If new seals didn’t stop the draft at one corner, the door itself might be out of line. Common causes:
- Loose top hinge. The door sags, the latch side drops, and a gap opens at the top corner. Tighten the hinge screws, or swap one for a 3-inch screw that reaches the framing.
- Strike plate set too far out. The door latches but doesn’t pull tight against the seal. Moving the strike in a little can fix it.
- Warped door. Some older wood doors bow. Weatherstripping can only cover so much.
If the frame is rotted or the door is warped badly, replacement might make more sense than chasing gaps. My post on repairing and refreshing your front door covers what’s worth fixing.
Northeast Ohio Tips
- Cold weather install: the DOE recommends installing on clean, dry surfaces at temperatures above 20°F. Adhesive products really want warmer than that, so keep the strip inside until you’re ready and do adhesive work on a milder day.
- Frozen bottoms: if snow and ice build up at your threshold, a sweep that drags hard will tear fast. Keep the step clear.
- Older homes: a lot of East Side houses have frames that aren’t perfectly square anymore. Expect to adjust as you go instead of cutting everything at once.
Time, Difficulty and Common Mistakes
Time: about 30 to 60 minutes for a kerf-in strip on one door. Add time if you’re pulling the door for a new door bottom or adjusting hinges.
Difficulty: easy to moderate. Kerf-in is beginner-friendly. Door bottoms and older doors take more patience.
Common mistakes:
- Buying the wrong profile, so the strip won’t stay in the kerf.
- Splicing short pieces together on a side instead of using one continuous strip.
- Gaps at the top corners.
- A seal so thick the door won’t latch, which strains the latch and frame.
- Covering a door that needs adjusting with more and more weatherstripping.
DIY or Call a Guy?
DIY it if you have a standard kerf-in door and the door closes evenly. This is one of the better beginner projects in the house: cheap, fast, and you’ll feel the difference.
Call someone if the door sags or rubs, the threshold or frame is rotted, you need the door off its hinges and don’t have a second person, or you’ve already replaced the seals and still have a draft. At that point it’s usually a door adjustment problem, and that’s where an extra set of hands and experience help. If you’re not sure what a handyman covers, see what a handyman can actually fix.
Local to Euclid or Cleveland’s east side? I install weatherstripping and adjust doors myself. See my Handyman Time Blocks in Euclid & Cleveland page, or text me a photo at 216-800-5883.
FAQ
How often should door weatherstripping be replaced?
When it’s flattened, cracked, torn or no longer touching the door. Do the dollar bill test every fall before heating season.
Can I put new weatherstripping over the old?
No. Pull the old strip first. Layering it makes the door hard to close and the seal still won’t be even.
Should a door be hard to close after new weatherstripping?
A little stiff for the first few days is normal while the foam compresses. If you have to slam it to latch, the strip is too thick or the strike needs adjusting.
Door sweep or door bottom: which is better?
If your door has slots on its bottom edge, use a slide-on door bottom. If it doesn’t, a sweep on the inside face is the easier fix.
Does weatherstripping go on the door or the frame?
On the frame (jamb) for the sides and top. The sweep or door bottom goes on the door itself.

Scan to join our Loyalty Program, get a free coupon for your next service, and stay up to date on our services and articles.
Affiliate Note
Some of the links in this article are affiliate links. That simply means if you choose to buy through them, I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. I only recommend products I trust and would feel comfortable installing in my own home or a client’s home.
If you try something I recommended and it turns out to be anything less than a five-star experience, please let me know. I always want these recommendations to be genuinely helpful.
